[ LUGOS ] Teľave z modemom
Marko Hrastelj
marko.hrastelj na kiss.uni-lj.si
Ned Jul 18 00:34:05 CEST 1999
Pozdrav vsem skup!
Spet mam neki za vpra±at, sam ne se preveč smejat, če gre za res
preproste stvari(mogoče pa niso)
Prvo: moj modem je ena taka če±ka zadeva-CommWave 28.8 kbps PnP (ISA
jasno). Zadevo naj bi nekako usposobil z isapnp oziroma najprej s
pnpdump, ki naredi isapnp.conf datoteko, a očitno je neka napaka v njej,
pri zagonu jo javi v vrstici 51. Prilagam dve verziji datoteke
isapnp.conf (datoteki sta v v .txt obliki, ker sem ju kopiral v windows,
prva je nedotaknjena, drugo-isapnp1 pa sem posku±al urediti po spominu:)
©e nekaj, v win se modem nahaja na com4, a da ga sistem sploh najde pri
instalaciji na tem com portu, ga je treba prej instalirati na com 2 in
com 5, če pa pol zbri±e± katerega od njih, pa noče klicat- to je čist
resno... V isapnp.config bi modem bil tista kartica pod 02e8
Drugo: ali isapnp povsem instalira modem?
Četrto: če vpi±em modem v mtab in fstab, odkod sporočilo 'Not in
host:dir format' ?
Uporabljam Red Hat 6.0
Upam , da bo kdo poznal odgovore na moja vpra±anja. Mimogrede, a kdo
pozna kak±no dobro knjigo o linuxu, po moµnosti v sloven±čini, kjer bi
bilo na preprost način opisano, kako začne± z linuxom.
Mare
PS:Zakaj so v konzoli, ko da± ukaz setfont lat2-16 pol neke tur±ke črke
namesto na±ih ±umnikov?
# $Id: 373.html,v 1.1 2001/07/05 06:23:23 roman Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier 56 01 00 00 00 80 28 70 40
(DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
#Card 1: (serial identifier 56 01 00 00 00 80 28 70 40)
#Vendor Id PCP2880, Serial Number 16777216, checksum 0x56.
#Version 1.0, Vendor version 0.0
#ANSI string -->CommWave V.34PNP Data/Fax/Voice Modem<--
# Logical device id PCT2880
# Device support I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE PCP2880/16777216 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK))
# IRQ 3, 4, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
Logical device decodes 16 bit IO address lines
Minimum IO base address 0x02e8
Maximum IO base address 0x02e8
IO base alignment 8 bytes
Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x02e8) (CHECK))
IRQ 3, 4, 5, 7, 9, 10 or 11.
High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK))
# IRQ 3, 4, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK))
# IRQ 3, 4, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(NAME "PCP2880/16777216[0]{CommWave V.34PNP Data/Fax/Voice Modem}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
# $Id: 373.html,v 1.1 2001/07/05 06:23:23 roman Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier 56 01 00 00 00 80 28 70 40
(DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
#Card 1: (serial identifier 56 01 00 00 00 80 28 70 40)
#Vendor Id PCP2880, Serial Number 16777216, checksum 0x56.
#Version 1.0, Vendor version 0.0
#ANSI string -->CommWave V.34PNP Data/Fax/Voice Modem<--
# Logical device id PCT2880
# Device support I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3a
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE PCP2880/16777216 (LD 0
# Multiple choice time, choose one only !
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK))
# IRQ 3, 4, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
Logical device decodes 16 bit IO address lines
Minimum IO base address 0x02e8
Maximum IO base address 0x02e8
IO base alignment 8 bytes
Number of IO addresses required: 8
(IO 0 (SIZE 8) (BASE 0x02e8) (CHECK))
IRQ 3, 4, 5, 7, 9, 10 or 11.
High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK))
# IRQ 3, 4, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK))
# IRQ 3, 4, 5, 7, 9, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(NAME "PCP2880/16777216[0]{CommWave V.34PNP Data/Fax/Voice Modem}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
Dodatne informacije o seznamu Starilist