[LUGOS] hmm... nov kernel, problem z cdrom-om!
Tomaž Toplak
Tomaz.Toplak at gmx.net
Fri Sep 24 21:45:24 CEST 2004
Hmm.. najbolj banalno je, da je bil glavni problem BIOS!
Prej sem za kernel 2.4 imel nastavljen bios tako, da je prepoznal SATA
diske kot primary PATA, kernel 2.6 pa podpira SATA diske tudi normalno
in je malo zmeden pri oni nastavitvi:)
Zdaj dela, moram še probat kaj je na tem, če lahko snemam cd-je.
lp
Hvala za pomoč:)
V pet, 24.09.2004 ob 20:06 je Davor Guttierrez napisal(a):
> Jaz ga tu ne najdem. Očitno si kaj izpustil pri prevajanju kernela.
>
> LP,
>
> D.
>
>
> On Fri, 2004-09-24 at 20:00, Tomaž Toplak wrote:
> > če bo kdo s tega pameten, naj napiše, meni se vse zdi malo zelo
> > sumljivo:)
> > Je pa res, da sve razen cdromov dela!
> >
> > : 8K
> > CPU: L2 cache: 512K
> > CPU: Physical Processor ID: 0
> > CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
> > Intel machine check architecture supported.
> > Intel machine check reporting enabled on CPU#1.
> > CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> > CPU1: Thermal monitoring enabled
> > CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
> > Total of 2 processors activated (10338.30 BogoMIPS).
> > ENABLING IO-APIC IRQs
> > init IO_APIC IRQs
> > IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
> > 2-23 not connected.
> > ..TIMER: vector=0x31 pin1=2 pin2=-1
> > Using local APIC timer interrupts.
> > calibrating APIC timer ...
> > ..... CPU clock speed is 2598.0361 MHz.
> > ..... host bus clock speed is 199.0873 MHz.
> > checking TSC synchronization across 2 CPUs: passed.
> > Brought up 2 CPUs
> > CPU0: online
> > domain 0: span 3
> > groups: 1 2
> > domain 1: span 3
> > groups: 3
> > CPU1: online
> > domain 0: span 3
> > groups: 2 1
> > domain 1: span 3
> > groups: 3
> > checking if image is initramfs...it isn't (ungzip failed); looks like an
> > initrd
> > Freeing initrd memory: 4188k freed
> > NET: Registered protocol family 16
> > PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
> > PCI: Using configuration type 1
> > mtrr: v2.0 (20020519)
> > ACPI: Subsystem revision 20040326
> > ACPI: Interpreter enabled
> > ACPI: Using IOAPIC for interrupt routing
> > ACPI: PCI Root Bridge [PCI0] (00:00)
> > PCI: Probing PCI hardware (bus 00)
> > PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
> > PCI: Transparent bridge - 0000:00:1e.0
> > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
> > disabled.
> > ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> > ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> > Linux Plug and Play Support v0.97 (c) Adam Belay
> > PnPBIOS: Scanning system for PnP BIOS support...
> > PnPBIOS: Found PnP BIOS installation structure at 0xc00f5580
> > PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x616a, dseg 0xf0000
> > PNPBIOS fault.. attempting recovery.
> > PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to
> > continue
> > PnPBIOS: You may need to reboot with the "nobiospnp" option to operate
> > stably
> > PnPBIOS: Check with your vendor for an updated BIOS
> > PnPBIOS: get_dev_node: unexpected status 0x28
> > PnPBIOS: 6 nodes reported by PnP BIOS; 6 recorded by driver
> > PCI: Using ACPI for IRQ routing
> > ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
> > ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
> > ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
> > ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169
> > ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
> > ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185
> > ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201
> > ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201
> > ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
> > ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 209
> > ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 23 (level, low) -> IRQ 193
> > ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 217
> > ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
> > number of MP IRQ sources: 15.
> > number of IO-APIC #2 registers: 24.
> > testing the IO APIC.......................
> > IO APIC #2......
> > .... register #00: 02000000
> > ....... : physical APIC id: 02
> > ....... : Delivery Type: 0
> > ....... : LTS : 0
> > .... register #01: 00178020
> > ....... : max redirection entries: 0017
> > ....... : PRQ implemented: 1
> > ....... : IO APIC version: 0020
> > .... IRQ redirection table:
> > NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
> > 00 000 00 1 0 0 0 0 0 0 00
> > 01 003 03 0 0 0 0 0 1 1 39
> > 02 003 03 0 0 0 0 0 1 1 31
> > 03 003 03 0 0 0 0 0 1 1 41
> > 04 003 03 0 0 0 0 0 1 1 49
> > 05 003 03 0 0 0 0 0 1 1 51
> > 06 003 03 0 0 0 0 0 1 1 59
> > 07 003 03 0 0 0 0 0 1 1 61
> > 08 003 03 0 0 0 0 0 1 1 69
> > 09 003 03 0 1 0 0 0 1 1 71
> > 0a 003 03 0 0 0 0 0 1 1 79
> > 0b 003 03 0 0 0 0 0 1 1 81
> > 0c 003 03 0 0 0 0 0 1 1 89
> > 0d 003 03 0 0 0 0 0 1 1 91
> > 0e 003 03 0 0 0 0 0 1 1 99
> > 0f 003 03 0 0 0 0 0 1 1 A1
> > 10 003 03 1 1 0 1 0 1 1 A9
> > 11 003 03 1 1 0 1 0 1 1 C9
> > 12 003 03 1 1 0 1 0 1 1 B9
> > 13 003 03 1 1 0 1 0 1 1 B1
> > 14 003 03 1 1 0 1 0 1 1 D1
> > 15 000 00 1 0 0 0 0 0 0 00
> > 16 003 03 1 1 0 1 0 1 1 D9
> > 17 003 03 1 1 0 1 0 1 1 C1
> > Using vector-based indexing
> > IRQ to pin mappings:
> > IRQ0 -> 0:2
> > IRQ1 -> 0:1
> > IRQ3 -> 0:3
> > IRQ4 -> 0:4
> > IRQ5 -> 0:5
> > IRQ6 -> 0:6
> > IRQ7 -> 0:7
> > IRQ8 -> 0:8
> > IRQ9 -> 0:9
> > IRQ10 -> 0:10
> > IRQ11 -> 0:11
> > IRQ12 -> 0:12
> > IRQ13 -> 0:13
> > IRQ14 -> 0:14
> > IRQ15 -> 0:15
> > IRQ169 -> 0:16
> > IRQ201 -> 0:17
> > IRQ185 -> 0:18
> > IRQ177 -> 0:19
> > IRQ209 -> 0:20
> > IRQ217 -> 0:22
> > IRQ193 -> 0:23
> > .................................... done.
> > vesafb: probe of vesafb0 failed with error -6
> > Starting balanced_irq
> > highmem bounce pool size: 64 pages
> > VFS: Disk quotas dquot_6.5.1
> > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> > devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
> > devfs: boot_options: 0x0
> > Initializing Cryptographic API
> > isapnp: Scanning for PnP cards...
> > isapnp: No Plug & Play device found
> > Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
> > enabled
> > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> > ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> > serio: i8042 AUX port at 0x60,0x64 irq 12
> > serio: i8042 KBD port at 0x60,0x64 irq 1
> > input: AT Translated Set 2 keyboard on isa0060/serio0
> > NET: Registered protocol family 2
> > IP: routing cache hash table of 8192 buckets, 64Kbytes
> > TCP: Hash tables configured (established 262144 bind 65536)
> > NET: Registered protocol family 8
> > NET: Registered protocol family 20
> > ACPI: (supports S0 S1 S3 S4 S5)
> > RAMDISK: cramfs filesystem found at block 0
> > RAMDISK: Loading 4188 blocks [1 disk] into ram disk... \
> >
> > done.
> > VFS: Mounted root (cramfs filesystem) readonly.
> > Freeing unused kernel memory: 188k freed
> > NET: Registered protocol family 1
> > SCSI subsystem initialized
> > libata version 1.02 loaded.
> > ata_piix version 1.02
> > ata_piix: combined mode detected
> > ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185
> > PCI: Setting latency timer of device 0000:00:1f.2 to 64
> > ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFC00 irq 14
> > ata1: dev 0 cfg 49:2f00 82:7c6b 83:7b09 84:4003 85:7c69 86:3a01 87:4003
> > 88:207f
> > ata1: dev 0 ATA, max UDMA/133, 240121728 sectors:
> > ata1: dev 0 configured for UDMA/133
> > scsi0 : ata_piix
> > Using anticipatory io scheduler
> > Vendor: ATA Model: Maxtor 6Y120M0 Rev: YAR5
> > Type: Direct-Access ANSI SCSI revision: 05
> > ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xFC08 irq 15
> > ata2: dev 0 cfg 49:0b00 82:4218 83:4000 84:4000 85:4218 86:0000 87:4000
> > 88:0407
> > ata2: dev 0 ATAPI, max UDMA/33
> > ata2: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
> > 88:0407
> > ata2: dev 1 ATAPI, max UDMA/33
> > ata2: dev 0 configured for UDMA/33
> > ata2: dev 1 configured for UDMA/33
> > scsi1 : ata_piix
> > SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
> > SCSI device sda: drive cache: write back
> > /dev/scsi/host0/bus0/target0/lun0: p1 p2 p4 < p5 p6 >
> > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> > idebus=xx
> > ide0: I/O resource 0x1F0-0x1F7 not free.
> > ide0: ports already in use, skipping probe
> > ide1: I/O resource 0x170-0x177 not free.
> > ide1: ports already in use, skipping probe
> > NTFS driver 2.1.15 [Flags: R/O MODULE].
> > kjournald starting. Commit interval 5 seconds
> > EXT3-fs: mounted filesystem with ordered data mode.
> > EXT3 FS on sda2, internal journal
> > Real Time Clock Driver v1.12
> > ieee1394: Initialized config rom entry `ip1394'
> > sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
> > ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
> > ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 209
> > ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209]
> > MMIO=[feaff800-feafffff] Max Packet=[2048]
> > ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 217
> > sk98lin: Network Device Driver v6.23
> > (C)Copyright 1999-2004 Marvell(R).
> > ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 217
> > eth0: 3Com Gigabit LOM (3C940)
> > PrefPort:A RlmtMode:Check Link State
> > usbcore: registered new driver usbfs
> > usbcore: registered new driver hub
> > ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
> > ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
> > Controller
> > PCI: Setting latency timer of device 0000:00:1d.7 to 64
> > ehci_hcd 0000:00:1d.7: irq 193, pci mem f8900c00
> > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
> > PCI: cache line size of 128 is not supported by device 0000:00:1d.7
> > ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
> > hub 1-0:1.0: USB hub found
> > hub 1-0:1.0: 8 ports detected
> > ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800001d9286]
> > ip1394: $Rev: 1224 $ Ben Collins <bcollins at debian.org>
> > ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> > Linux agpgart interface v0.100 (c) Dave Jones
> > agpgart: Detected an Intel 865 Chipset.
> > agpgart: Maximum main memory to use for agp memory: 941M
> > agpgart: AGP aperture is 128M @ 0xf0000000
> > cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
> > pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> > pciehp: PCI Express Hot Plug Controller Driver version: 0.4
> > shpchp: shpc_init : shpc_cap_offset == 0
> > shpchp: shpc_init : shpc_cap_offset == 0
> > shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> > USB Universal Host Controller Interface driver v2.2
> > ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
> > uhci_hcd 0000:00:1d.0: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
> > PCI: Setting latency timer of device 0000:00:1d.0 to 64
> > uhci_hcd 0000:00:1d.0: irq 169, io base 0000eec0
> > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
> > hub 2-0:1.0: USB hub found
> > hub 2-0:1.0: 2 ports detected
> > ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
> > uhci_hcd 0000:00:1d.1: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
> > PCI: Setting latency timer of device 0000:00:1d.1 to 64
> > uhci_hcd 0000:00:1d.1: irq 177, io base 0000ef00
> > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
> > hub 3-0:1.0: USB hub found
> > hub 3-0:1.0: 2 ports detected
> > ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
> > uhci_hcd 0000:00:1d.2: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
> > PCI: Setting latency timer of device 0000:00:1d.2 to 64
> > uhci_hcd 0000:00:1d.2: irq 185, io base 0000ef20
> > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
> > hub 4-0:1.0: USB hub found
> > hub 4-0:1.0: 2 ports detected
> > ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169
> > uhci_hcd 0000:00:1d.3: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
> > PCI: Setting latency timer of device 0000:00:1d.3 to 64
> > uhci_hcd 0000:00:1d.3: irq 169, io base 0000ef40
> > uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
> > hub 5-0:1.0: USB hub found
> > hub 5-0:1.0: 2 ports detected
> > hw_random hardware driver 1.0.0 loaded
> > ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201
> > PCI: Setting latency timer of device 0000:00:1f.5 to 64
> > AC'97 0 analog subsections not ready
> > intel8x0_measure_ac97_clock: measured 49504 usecs
> > intel8x0: clocking to 48000
> > ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
> > drivers/media/dvb/b2c2/skystar2.c: FlexCopII(rev.130) chip found
> > drivers/media/dvb/b2c2/skystar2.c: the chip has 6 hardware filters
> > DVB: registering new adapter (Technisat SkyStar2 driver).
> > NET: Registered protocol family 17
> > eth0: network connection up using port A
> > speed: 100
> > autonegotiation: yes
> > duplex mode: full
> > flowctrl: symmetric
> > irq moderation: disabled
> > scatter-gather: enabled
> > eth0: network connection down
> > eth0: network connection up using port A
> > speed: 100
> > autonegotiation: yes
> > duplex mode: full
> > flowctrl: symmetric
> > irq moderation: disabled
> > scatter-gather: enabled
> > parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
> > parport0: irq 7 detected
> > lp0: using parport0 (polling).
> > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> > apm: disabled - APM is not SMP safe.
> > fglrx: no version for "struct_module" found: kernel tainted.
> > fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies,
> > Starnberg, GERMANY' taints kernel.
> > [fglrx] Maximum main memory to use for locked dma buffers: 928 MBytes.
> > ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
> > [fglrx] module loaded - fglrx 3.12.0 [Jul 16 2004] on minor 0
> > [fglrx] AGP detected, AgpState = 0x1f004a1b (hardware caps of chipset)
> > agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
> > agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
> > agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
> > [fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
> > [fglrx] free AGP = 121909248
> > [fglrx] max AGP = 121909248
> > [fglrx] free LFB = 119537664
> > [fglrx] max LFB = 119537664
> > [fglrx] free Inv = 0
> > [fglrx] max Inv = 0
> > [fglrx] total Inv = 0
> > [fglrx] total TIM = 0
> > [fglrx] total FB = 0
> > [fglrx] total AGP = 32768
> > input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
> > mice: PS/2 mouse device common for all mice
> > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> > apm: disabled - APM is not SMP safe.
> > [fglrx] free AGP = 121909248
> > [fglrx] max AGP = 121909248
> > [fglrx] free LFB = 119537664
> > [fglrx] max LFB = 119537664
> > [fglrx] free Inv = 0
> > [fglrx] max Inv = 0
> > [fglrx] total Inv = 0
> > [fglrx] total TIM = 0
> > [fglrx] total FB = 0
> > [fglrx] total AGP = 32768
> > NET: Registered protocol family 10
> > Disabled Privacy Extensions on device c036e540(lo)
> > IPv6 over IPv4 tunneling driver
> > inserting floppy driver for 2.6.8-1-smp
> > Floppy drive(s): fd0 is 1.44M
> > FDC 0 is a post-1991 82077
> > eth0: no IPv6 routers present
> >
> > Hvala!
> >
> >
> > V pet, 24.09.2004 ob 19:24 je Davor Guttierrez napisal(a):
> > > Hi
> > >
> > > V konzoli uporabi dmesg |more in preglej kje se pojavi beseda CDROM ali
> > > kaj podobnega. Recimo nekaj takega:
> > >
> > > hdc: ASUS CRW-5232AS, ATAPI CD/DVD-ROM drive
> > > hdd: _NEC DVD_RW ND-2510A, ATAPI CD/DVD-ROM drive
> > >
> > > LP,
> > >
> > > D.
> > >
> >
More information about the lugos-list
mailing list