[LUGOS] hmm... nov kernel, problem z cdrom-om!
Davor Guttierrez
davor at guttierrez.org
Fri Sep 24 20:06:20 CEST 2004
Jaz ga tu ne najdem. Očitno si kaj izpustil pri prevajanju kernela.
LP,
D.
On Fri, 2004-09-24 at 20:00, Tomaž Toplak wrote:
> če bo kdo s tega pameten, naj napiše, meni se vse zdi malo zelo
> sumljivo:)
> Je pa res, da sve razen cdromov dela!
>
> : 8K
> CPU: L2 cache: 512K
> CPU: Physical Processor ID: 0
> CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#1.
> CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
> CPU1: Thermal monitoring enabled
> CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
> Total of 2 processors activated (10338.30 BogoMIPS).
> ENABLING IO-APIC IRQs
> init IO_APIC IRQs
> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
> 2-23 not connected.
> ..TIMER: vector=0x31 pin1=2 pin2=-1
> Using local APIC timer interrupts.
> calibrating APIC timer ...
> ..... CPU clock speed is 2598.0361 MHz.
> ..... host bus clock speed is 199.0873 MHz.
> checking TSC synchronization across 2 CPUs: passed.
> Brought up 2 CPUs
> CPU0: online
> domain 0: span 3
> groups: 1 2
> domain 1: span 3
> groups: 3
> CPU1: online
> domain 0: span 3
> groups: 2 1
> domain 1: span 3
> groups: 3
> checking if image is initramfs...it isn't (ungzip failed); looks like an
> initrd
> Freeing initrd memory: 4188k freed
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20040326
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (00:00)
> PCI: Probing PCI hardware (bus 00)
> PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
> disabled.
> ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> PnPBIOS: Scanning system for PnP BIOS support...
> PnPBIOS: Found PnP BIOS installation structure at 0xc00f5580
> PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x616a, dseg 0xf0000
> PNPBIOS fault.. attempting recovery.
> PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to
> continue
> PnPBIOS: You may need to reboot with the "nobiospnp" option to operate
> stably
> PnPBIOS: Check with your vendor for an updated BIOS
> PnPBIOS: get_dev_node: unexpected status 0x28
> PnPBIOS: 6 nodes reported by PnP BIOS; 6 recorded by driver
> PCI: Using ACPI for IRQ routing
> ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
> ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
> ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
> ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169
> ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
> ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185
> ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201
> ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
> ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 209
> ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 23 (level, low) -> IRQ 193
> ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 217
> ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
> number of MP IRQ sources: 15.
> number of IO-APIC #2 registers: 24.
> testing the IO APIC.......................
> IO APIC #2......
> .... register #00: 02000000
> ....... : physical APIC id: 02
> ....... : Delivery Type: 0
> ....... : LTS : 0
> .... register #01: 00178020
> ....... : max redirection entries: 0017
> ....... : PRQ implemented: 1
> ....... : IO APIC version: 0020
> .... IRQ redirection table:
> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
> 00 000 00 1 0 0 0 0 0 0 00
> 01 003 03 0 0 0 0 0 1 1 39
> 02 003 03 0 0 0 0 0 1 1 31
> 03 003 03 0 0 0 0 0 1 1 41
> 04 003 03 0 0 0 0 0 1 1 49
> 05 003 03 0 0 0 0 0 1 1 51
> 06 003 03 0 0 0 0 0 1 1 59
> 07 003 03 0 0 0 0 0 1 1 61
> 08 003 03 0 0 0 0 0 1 1 69
> 09 003 03 0 1 0 0 0 1 1 71
> 0a 003 03 0 0 0 0 0 1 1 79
> 0b 003 03 0 0 0 0 0 1 1 81
> 0c 003 03 0 0 0 0 0 1 1 89
> 0d 003 03 0 0 0 0 0 1 1 91
> 0e 003 03 0 0 0 0 0 1 1 99
> 0f 003 03 0 0 0 0 0 1 1 A1
> 10 003 03 1 1 0 1 0 1 1 A9
> 11 003 03 1 1 0 1 0 1 1 C9
> 12 003 03 1 1 0 1 0 1 1 B9
> 13 003 03 1 1 0 1 0 1 1 B1
> 14 003 03 1 1 0 1 0 1 1 D1
> 15 000 00 1 0 0 0 0 0 0 00
> 16 003 03 1 1 0 1 0 1 1 D9
> 17 003 03 1 1 0 1 0 1 1 C1
> Using vector-based indexing
> IRQ to pin mappings:
> IRQ0 -> 0:2
> IRQ1 -> 0:1
> IRQ3 -> 0:3
> IRQ4 -> 0:4
> IRQ5 -> 0:5
> IRQ6 -> 0:6
> IRQ7 -> 0:7
> IRQ8 -> 0:8
> IRQ9 -> 0:9
> IRQ10 -> 0:10
> IRQ11 -> 0:11
> IRQ12 -> 0:12
> IRQ13 -> 0:13
> IRQ14 -> 0:14
> IRQ15 -> 0:15
> IRQ169 -> 0:16
> IRQ201 -> 0:17
> IRQ185 -> 0:18
> IRQ177 -> 0:19
> IRQ209 -> 0:20
> IRQ217 -> 0:22
> IRQ193 -> 0:23
> .................................... done.
> vesafb: probe of vesafb0 failed with error -6
> Starting balanced_irq
> highmem bounce pool size: 64 pages
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
> devfs: boot_options: 0x0
> Initializing Cryptographic API
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
> enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> input: AT Translated Set 2 keyboard on isa0060/serio0
> NET: Registered protocol family 2
> IP: routing cache hash table of 8192 buckets, 64Kbytes
> TCP: Hash tables configured (established 262144 bind 65536)
> NET: Registered protocol family 8
> NET: Registered protocol family 20
> ACPI: (supports S0 S1 S3 S4 S5)
> RAMDISK: cramfs filesystem found at block 0
> RAMDISK: Loading 4188 blocks [1 disk] into ram disk... \
>
> done.
> VFS: Mounted root (cramfs filesystem) readonly.
> Freeing unused kernel memory: 188k freed
> NET: Registered protocol family 1
> SCSI subsystem initialized
> libata version 1.02 loaded.
> ata_piix version 1.02
> ata_piix: combined mode detected
> ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFC00 irq 14
> ata1: dev 0 cfg 49:2f00 82:7c6b 83:7b09 84:4003 85:7c69 86:3a01 87:4003
> 88:207f
> ata1: dev 0 ATA, max UDMA/133, 240121728 sectors:
> ata1: dev 0 configured for UDMA/133
> scsi0 : ata_piix
> Using anticipatory io scheduler
> Vendor: ATA Model: Maxtor 6Y120M0 Rev: YAR5
> Type: Direct-Access ANSI SCSI revision: 05
> ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xFC08 irq 15
> ata2: dev 0 cfg 49:0b00 82:4218 83:4000 84:4000 85:4218 86:0000 87:4000
> 88:0407
> ata2: dev 0 ATAPI, max UDMA/33
> ata2: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
> 88:0407
> ata2: dev 1 ATAPI, max UDMA/33
> ata2: dev 0 configured for UDMA/33
> ata2: dev 1 configured for UDMA/33
> scsi1 : ata_piix
> SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
> SCSI device sda: drive cache: write back
> /dev/scsi/host0/bus0/target0/lun0: p1 p2 p4 < p5 p6 >
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> ide0: I/O resource 0x1F0-0x1F7 not free.
> ide0: ports already in use, skipping probe
> ide1: I/O resource 0x170-0x177 not free.
> ide1: ports already in use, skipping probe
> NTFS driver 2.1.15 [Flags: R/O MODULE].
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> EXT3 FS on sda2, internal journal
> Real Time Clock Driver v1.12
> ieee1394: Initialized config rom entry `ip1394'
> sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
> ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
> ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 209
> ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209]
> MMIO=[feaff800-feafffff] Max Packet=[2048]
> ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 217
> sk98lin: Network Device Driver v6.23
> (C)Copyright 1999-2004 Marvell(R).
> ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 217
> eth0: 3Com Gigabit LOM (3C940)
> PrefPort:A RlmtMode:Check Link State
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
> ehci_hcd 0000:00:1d.7: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
> Controller
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: irq 193, pci mem f8900c00
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
> PCI: cache line size of 128 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800001d9286]
> ip1394: $Rev: 1224 $ Ben Collins <bcollins at debian.org>
> ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> Linux agpgart interface v0.100 (c) Dave Jones
> agpgart: Detected an Intel 865 Chipset.
> agpgart: Maximum main memory to use for agp memory: 941M
> agpgart: AGP aperture is 128M @ 0xf0000000
> cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> pciehp: PCI Express Hot Plug Controller Driver version: 0.4
> shpchp: shpc_init : shpc_cap_offset == 0
> shpchp: shpc_init : shpc_cap_offset == 0
> shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> USB Universal Host Controller Interface driver v2.2
> ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
> uhci_hcd 0000:00:1d.0: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #1
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: irq 169, io base 0000eec0
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
> uhci_hcd 0000:00:1d.1: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #2
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: irq 177, io base 0000ef00
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
> uhci_hcd 0000:00:1d.2: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #3
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: irq 185, io base 0000ef20
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169
> uhci_hcd 0000:00:1d.3: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI #4
> PCI: Setting latency timer of device 0000:00:1d.3 to 64
> uhci_hcd 0000:00:1d.3: irq 169, io base 0000ef40
> uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
> hub 5-0:1.0: USB hub found
> hub 5-0:1.0: 2 ports detected
> hw_random hardware driver 1.0.0 loaded
> ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> AC'97 0 analog subsections not ready
> intel8x0_measure_ac97_clock: measured 49504 usecs
> intel8x0: clocking to 48000
> ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
> drivers/media/dvb/b2c2/skystar2.c: FlexCopII(rev.130) chip found
> drivers/media/dvb/b2c2/skystar2.c: the chip has 6 hardware filters
> DVB: registering new adapter (Technisat SkyStar2 driver).
> NET: Registered protocol family 17
> eth0: network connection up using port A
> speed: 100
> autonegotiation: yes
> duplex mode: full
> flowctrl: symmetric
> irq moderation: disabled
> scatter-gather: enabled
> eth0: network connection down
> eth0: network connection up using port A
> speed: 100
> autonegotiation: yes
> duplex mode: full
> flowctrl: symmetric
> irq moderation: disabled
> scatter-gather: enabled
> parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
> parport0: irq 7 detected
> lp0: using parport0 (polling).
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> apm: disabled - APM is not SMP safe.
> fglrx: no version for "struct_module" found: kernel tainted.
> fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies,
> Starnberg, GERMANY' taints kernel.
> [fglrx] Maximum main memory to use for locked dma buffers: 928 MBytes.
> ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
> [fglrx] module loaded - fglrx 3.12.0 [Jul 16 2004] on minor 0
> [fglrx] AGP detected, AgpState = 0x1f004a1b (hardware caps of chipset)
> agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
> agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
> agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
> [fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
> [fglrx] free AGP = 121909248
> [fglrx] max AGP = 121909248
> [fglrx] free LFB = 119537664
> [fglrx] max LFB = 119537664
> [fglrx] free Inv = 0
> [fglrx] max Inv = 0
> [fglrx] total Inv = 0
> [fglrx] total TIM = 0
> [fglrx] total FB = 0
> [fglrx] total AGP = 32768
> input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
> mice: PS/2 mouse device common for all mice
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> apm: disabled - APM is not SMP safe.
> [fglrx] free AGP = 121909248
> [fglrx] max AGP = 121909248
> [fglrx] free LFB = 119537664
> [fglrx] max LFB = 119537664
> [fglrx] free Inv = 0
> [fglrx] max Inv = 0
> [fglrx] total Inv = 0
> [fglrx] total TIM = 0
> [fglrx] total FB = 0
> [fglrx] total AGP = 32768
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c036e540(lo)
> IPv6 over IPv4 tunneling driver
> inserting floppy driver for 2.6.8-1-smp
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> eth0: no IPv6 routers present
>
> Hvala!
>
>
> V pet, 24.09.2004 ob 19:24 je Davor Guttierrez napisal(a):
> > Hi
> >
> > V konzoli uporabi dmesg |more in preglej kje se pojavi beseda CDROM ali
> > kaj podobnega. Recimo nekaj takega:
> >
> > hdc: ASUS CRW-5232AS, ATAPI CD/DVD-ROM drive
> > hdd: _NEC DVD_RW ND-2510A, ATAPI CD/DVD-ROM drive
> >
> > LP,
> >
> > D.
> >
>
--
Lep pozdrav,
Davor Guttierrez; Sistemski inženir; RHCE
|---------------------------------------|
http://www.cadis.si; davor.guttierrez at cadis.si--|
http://www.d-mashina.net; davor at guttierrez.org--|
<---------------------------------->
BloG - http://www.d-mashina.net/blog
<---------------------------------->
More information about the lugos-list
mailing list