[LUGOS] Digitalni fotoaparat

[Matej Zerovnik - LeVaK]

On Monday 24 of February 2003 14:08, Matej Zerovnik - LeVaK wrote:
> Vceraj sem dobil fotoaparat Minolta DImage 7i. Mal poslikam in grem za PC.
> Prklucm USB, naloadam module... Vse kot po maslu:
>
> Feb 24 13:56:33 etela kernel: usb-storage: *** thread sleeping.
> Feb 24 13:56:33 etela kernel:   Vendor: MINOLTA   Model: DIMAGE  CAMERA
> Rev: 1.00
> Feb 24 13:56:33 etela kernel:   Type:   Direct-Access
> ANSI SCSI revision: 02
> Feb 24 13:56:33 etela kernel: usb-storage: queuecommand() called
> Feb 24 13:56:34 etela kernel: SCSI device sda: 31264 512-byte hdwr sectors
> (16 MB)
> Feb 24 13:56:34 etela kernel:  sda1
>
> potem mountam z mount /dev/sda1 /mnt/digital in fotoaparat se diskonekta
> sistem pa vrne no partition table found + povno errorjev.
>
> Feb 24 13:57:02 etela kernel: uhci.c: uhci_result_interrupt/bulk() failed
> with status 440000
> Feb 24 13:57:02 etela kernel: [cf5a80c0] link (0f5a8092) element (0884a000)
> Feb 24 13:57:02 etela kernel:   0: [c884a000] link (0884a030) e0 Stalled
> CRC/Timeo Length=f MaxLen=f DT0 EndPt=3 Dev=3, PID=e1(OUT) (buf=0
> Feb 24 13:57:02 etela kernel:   1: [c884a030] link (00000001) e3 SPD IOC
> Active Length=0 MaxLen=e DT1 EndPt=3 Dev=3, PID=e1(OUT) (buf=032f
> Feb 24 13:57:02 etela kernel:
> Feb 24 13:57:02 etela kernel: usb-storage: Bulk command transfer
> result=-110 Feb 24 13:57:02 etela kernel: usb-storage: -- transport
> indicates error, resetting
> Feb 24 13:57:02 etela kernel: usb-storage: Bulk reset requested
> Feb 24 13:57:02 etela kernel: uhci.c: uhci_result_control() failed with
> status 440000
> Feb 24 13:57:02 etela kernel: [cf5a80f0] link (0f5a8062) element (0884a000)
> Feb 24 13:57:02 etela kernel:   0: [c884a000] link (0884a030) e0 Stalled
> CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf
> Feb 24 13:57:02 etela kernel:   1: [c884a030] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=69(IN) (buf=00Feb 24 13:57:02
> etela kernel: usb-storage: -- releasing main URB
> Feb 24 13:57:02 etela kernel:
>
> -------------- Tega namece okoli 400 vrstic -------------------
>
> Feb 24 13:57:02 etela kernel: usb.c: USB disconnect on device 3Feb 24
> 13:57:02 etela kernel: usb-storage: -- releasing main URB
> Feb 24 13:57:02 etela kernel: usb-storage: -- usb_unlink_urb() returned -19
> Feb 24 13:57:02 etela kernel: usb.c: kusbd: /sbin/hotplug remove 3
>
> Feb 24 13:57:02 etela kernel: usb-storage: queuecommand() called
> Feb 24 13:57:02 etela kernel: usb-storage: *** thread awakened.
> Feb 24 13:57:02 etela kernel: usb-storage: Request is for removed device
> Feb 24 13:57:02 etela kernel: usb-storage: scsi cmd done, result=0x2
> Feb 24 13:57:02 etela kernel: usb-storage: *** thread sleeping.
> Feb 24 13:57:02 etela kernel: usb-storage: queuecommand() called
> Feb 24 13:57:02 etela kernel: usb-storage: *** thread awakened.
> Feb 24 13:57:02 etela kernel: usb-storage: Request is for removed device
> Feb 24 13:57:02 etela kernel: usb-storage: scsi cmd done, result=0x2
> Feb 24 13:57:02 etela kernel: usb-storage: *** thread sleeping.
> Feb 24 13:57:02 etela kernel: usb-storage: queuecommand() called
> Feb 24 13:57:02 etela kernel: usb-storage: *** thread awakened.
> Feb 24 13:57:02 etela kernel: usb-storage: Request is for removed device
> Feb 24 13:57:02 etela kernel: usb-storage: scsi cmd done, result=0x2
> Feb 24 13:57:02 etela kernel: usb-storage: *** thread sleeping.
> Feb 24 13:57:02 etela kernel: sda : READ CAPACITY failed.
> Feb 24 13:57:02 etela kernel: sda : status = 1, message = 00, host = 0,
> driver = 08
> Feb 24 13:57:02 etela kernel: Info fld=0xa00 (nonstd), Current sd00:00:
> sense key Not Ready
> Feb 24 13:57:02 etela kernel: sda : block size assumed to be 512 bytes,
> disk size 1GB.
> Feb 24 13:57:02 etela kernel:  sda: I/O error: dev 08:00, sector 0
> Feb 24 13:57:02 etela kernel:  I/O error: dev 08:00, sector 0
> Feb 24 13:57:02 etela kernel:  unable to read partition table
> Feb 24 13:57:02 etela kernel: uhci.c: root-hub INT complete: port1: 488
> port2: 580 data: 2
> Feb 24 13:57:02 etela kernel: hub.c: port 1, portstatus 100, change 2, 12
> Mb/s Feb 24 13:57:02 etela kernel: hub.c: port 1 enable change, status 100
> Feb 24 13:57:02 etela kernel: hub.c: port 2, portstatus 300, change 0, 1.5
> Mb/s
> Feb 24 13:57:03 etela kernel: usb-storage: usb_stor_exit() called
> Feb 24 13:57:03 etela kernel: usb-storage: -- calling usb_deregister()
> Feb 24 13:57:03 etela kernel: usb.c: deregistering driver usb-storage
> Feb 24 13:57:03 etela kernel: usb-storage: -- calling
> scsi_unregister_module() Feb 24 13:57:03 etela kernel: usb-storage:
> release() called for host usb-storage
> Feb 24 13:57:03 etela kernel: usb-storage: -- sending US_ACT_EXIT command
> to thread
> Feb 24 13:57:03 etela kernel: usb-storage: *** thread awakened.
> Feb 24 13:57:03 etela kernel: usb-storage: -- US_ACT_EXIT command received
>
>
> Se komu kaj sanja? meni se namrec ne vec:) Aja enak problem je na CF in IBM
> microdrive-u.
>
> LeVaK

Resil problem. V /usr/src/linux-2.4.19/drivers/usb/storage/unusual_devs.h
sej moral dodati pri Minolti tole:

                UNUSUAL_DEV( 0x0686, 0x4006, 0x0001, 0x0001,
                "Minolta",
                "Dimage 7",
                US_SC_SCSI, US_PR_BULK, NULL,
                US_FL_START_STOP ),

                UNUSUAL_DEV( 0x0686, 0x400b, 0x0001, 0x0001,
                "Minolta",
                "Dimage 7i",
                US_SC_SCSI, US_PR_BULK, NULL,
                US_FL_START_STOP ),

                UNUSUAL_DEV( 0x0686, 0x400f, 0x0001, 0x0001,
                "Minolta",
                "Dimage 7Hi",
                US_SC_SCSI, US_PR_BULK, NULL,
                US_FL_START_STOP ),

Tako.. Ce bo kdaj kdo imel problem.. tukaj je resitev:)

LeVaK