[ LUGOS ] HylaFax send problems

[Nejc Skoberne]

Zdravo.

Log:

Jan 27 11:31:42.28: [14731]: SESSION BEGIN 00000004 3860503881613
Jan 27 11:31:42.28: [14731]: SEND FAX: JOB 2 DEST 03881613 COMMID
00000004
Jan 27 11:31:42.28: [14731]: DELAY 2600 ms
Jan 27 11:31:44.88: [14731]: <--
[36:AT&B1&N0&S0S18=4S38.3=1E0V1Q0S0=0H0\r]
Jan 27 11:31:44.92: [14731]: --> [2:OK]
Jan 27 11:31:44.92: [14731]: <-- [21:ATS8=2S7=60&H3&D2&C1\r]
Jan 27 11:31:44.94: [14731]: --> [2:OK]
Jan 27 11:31:44.94: [14731]: <-- [14:AT+FCLASS=2.0\r]
Jan 27 11:31:44.97: [14731]: --> [2:OK]
Jan 27 11:31:44.97: [14731]: <-- [9:AT+FLO=2\r]
Jan 27 11:31:44.99: [14731]: --> [2:OK]
Jan 27 11:31:44.99: [14731]: <-- [9:AT+FPP=0\r]
Jan 27 11:31:45.01: [14731]: --> [2:OK]
Jan 27 11:31:45.01: [14731]: <-- [9:AT+FBO=0\r]
Jan 27 11:31:45.03: [14731]: --> [2:OK]
Jan 27 11:31:45.03: [14731]: <-- [10:AT+FCT=30\r]
Jan 27 11:31:45.05: [14731]: --> [2:OK]
Jan 27 11:31:45.05: [14731]: <-- [15:AT+FNR=1,1,1,1\r]
Jan 27 11:31:45.08: [14731]: --> [2:OK]
Jan 27 11:31:45.08: [14731]: <-- [9:AT+FIE=0\r]
Jan 27 11:31:45.11: [14731]: --> [2:OK]
Jan 27 11:31:45.11: [14731]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Jan 27 11:31:45.14: [14731]: --> [2:OK]
Jan 27 11:31:45.14: [14731]: <-- [5:ATM0\r]
Jan 27 11:31:45.16: [14731]: --> [2:OK]
Jan 27 11:31:45.17: [14731]: <-- [14:AT+FCLASS=2.0\r]
Jan 27 11:31:45.29: [14731]: --> [2:OK]
Jan 27 11:31:45.29: [14731]: <-- [9:AT+FLO=2\r]
Jan 27 11:31:45.41: [14731]: --> [2:OK]
Jan 27 11:31:45.41: [14731]: <-- [9:AT+FPP=0\r]
Jan 27 11:31:45.54: [14731]: --> [2:OK]
Jan 27 11:31:45.54: [14731]: <-- [9:AT+FBO=0\r]
Jan 27 11:31:45.67: [14731]: --> [2:OK]
Jan 27 11:31:45.67: [14731]: <-- [10:AT+FCT=30\r]
Jan 27 11:31:45.79: [14731]: --> [2:OK]
Jan 27 11:31:45.79: [14731]: <-- [15:AT+FNR=1,1,1,1\r]
Jan 27 11:31:45.92: [14731]: --> [2:OK]
Jan 27 11:31:45.92: [14731]: <-- [9:AT+FIE=0\r]
Jan 27 11:31:46.04: [14731]: --> [2:OK]
Jan 27 11:31:46.04: [14731]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Jan 27 11:31:46.17: [14731]: --> [2:OK]
Jan 27 11:31:46.17: [14731]: <-- [22:AT+FLI="NothingSetup"\r]
Jan 27 11:31:46.31: [14731]: --> [2:OK]
Jan 27 11:31:46.32: [14731]: DIAL 03881613
Jan 27 11:31:46.32: [14731]: <-- [13:ATDT03881613\r]
Jan 27 11:31:56.48: [14731]: --> [4:+FCO]
Jan 27 11:31:56.48: [14731]: --> [118:+FNF:00 00 0E 00 00 00 96 0F 01 07
00 10 05 02 95 C8 18 01 49 02 41 45 54 20 54 4F 4C 4D 49 4E 20 53 49 20
20 20 03   ]
Jan 27 11:31:56.49: [14731]: REMOTE NSF "00 00 0E 00 00 00 96 0F 01 07
00 10 05 02 95 C8 18 01 49 02 41 45 54 20 54 4F 4C 4D 49 4E 20 53 49 20
20 20 03"
Jan 27 11:31:56.60: [14731]: --> [26:+FCI:       +386 65 81613 ]
Jan 27 11:31:56.60: [14731]: REMOTE CSI "+386 65 81613"
Jan 27 11:31:56.60: [14731]: --> [20:+FIS:1,3,0,2,1,1,0,5]
Jan 27 11:31:56.61: [14731]: --> [2:OK]
Jan 27 11:31:56.61: [14731]: REMOTE best rate 9600 bit/s
Jan 27 11:31:56.61: [14731]: REMOTE max page width 1728 pixels in 215 mm
Jan 27 11:31:56.61: [14731]: REMOTE max unlimited page length
Jan 27 11:31:56.61: [14731]: REMOTE best vres 7.7 line/mm
Jan 27 11:31:56.61: [14731]: REMOTE best format 2-D MR
Jan 27 11:31:56.61: [14731]: REMOTE supports T.30 Annex A, ECM
Jan 27 11:31:56.61: [14731]: REMOTE best 20 ms/scanline
Jan 27 11:31:56.61: [14731]: USE 9600 bit/s
Jan 27 11:31:56.61: [14731]: USE 20 ms/scanline
Jan 27 11:31:56.61: [14731]: <-- [5:ATH0\r]
Jan 27 11:31:56.72: [14731]: --> [2:OK]
Jan 27 11:31:56.73: [14731]: SESSION END

Slackware 7.0, kernel 2.2.17, ZyXEL 2864I. Kot vidite se ustavi po tem,
ko nastavi "USE 20 ms/scanline". Kar naenkrat prekine. Kaksna ideja?

-- 
Nejc Skoberne
Grajska 5
5220 Tolmin
e-mail: nejko na varnost.org