<div>Lep pozdrav vsem..</div>
<div> </div>
<div>Mene zanima a ima kdo od članov liste nameščene gonilnike za zydas od projekta <font size="2"><strong>zd1211</strong>.ath.cx ?</font></div>
<div><font size="2"></font> </div>
<div><font size="2">Sem poskušal že spraševati na njihovi ineteni listi, pa imam težave s prijavo nanjo. Zato tudi sprašujem zdaj na Lugos listi.</font></div>
<div><font size="2"></font> </div>
<div><font size="2">Osnoven problem je, da mi gonilnik zapremza računalo tako zelo, da je nemogoče tudi tipkati v konzolo, saj se znaki pojavijo na ekrano po pol minute. Problem sem malo bolje opisal v angleščini za njihovo interno listo in dodal dmesg..
</font></div>
<div><font size="2"></font> </div>
<div><font size="2">Če kdo vidi kakšno napako bi bil zelo vesel namigov,</font></div>
<div><font size="2"></font> </div>
<div><font size="2">Lp,</font></div>
<div><font size="2">Janes</font></div>
<div> </div>
<div> </div>
<div>Subject: No wireless extensions or extreme cpu usage<br><br>Hi!<br><br>First I want to say thanks for great effort to everybody.<br>My story is this. I've been trying to compile this driver ever since v.52<br>(noob:), but I had no luck till now.
</div>
<div> </div>
<div>V.83 and a new slax install finaly builds the zd1221b module with no problems. I am using zd1211b cos of usb1.1 I have on my TP600. Modprobe loads it successfully and lsmod shows it loaded. And dmesg doesn't give out any suspicions there is something wrong..
<br>But there are no interfaces.. only the local loopback.. ifconfig wlanx or<br>ethx up doesn't work.. unknown interface: no such device<br><br>Then I tried to build zd1211 which builds perfectly too, even autoloads,<br>
has interfaces and I think it should connect, but the cpu usage is so high<br>it is imposibbly to work with computer (I have 300Mhz Thinkpad).. <br><br>I tried to search for a solution in archives, but didn't find nothing.
<br><br>The zd1211 gives out dmesg errors unlike the zd1211b<br><br>Hope somebody can make any sense out.<br><br>zd1211 - <a onclick="return top.js.OpenExtLink(window,event,this)" target="_blank" href="http://zd1211.ath.cx/">
http://zd1211.ath.cx/</a> - r83<br>Based on <a onclick="return top.js.OpenExtLink(window,event,this)" target="_blank" href="http://www.zydas.com.tw/">www.zydas.com.tw</a> driver version <a onclick="return top.js.OpenExtLink(window,event,this)" target="_blank" href="http://2.5.0.0/">
2.5.0.0</a><br>usb 1-1: reset full speed USB device using uhci_hcd and address 2<br>Release Ver = 4330<br>zd1211:bulk out: wMaxPacketSize = 40<br>zd1211:bulk in: wMaxPacketSize = 40<span></span> <br>zd1211:interrupt in: wMaxPacketSize = 40
<br>zd1211:interrupt in: int_interval = 1<br>zd1211:bulk out: wMaxPacketSize = 40 <br>EEPORM Ver = 4330<br>zd1211:USB Download Boot code success<br>zd1211:MAC address = 00:0e:2e:6c:1d:05<br>zd1211:AddrEntryTable = f7d4<br>
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)<br>zd1211:RF_Mode = 00000004 <br>PA type: 0<br>AiroHa AL2230RF<br>zd1211:Pure B-Mode<br>zd1211:AllowedChannel = 000007ff<br>zd1211:LinkLEDn = 200<br>
AllowedChannel = 000107ff<br>Region:48<br>zd1205: (exit) zd1205_config,<br>/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 2601 <br>zd1205: (exit) zd1205_init,<br>/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 8570
<br>usbcore: registered new driver zd1211<br>zd1205: (enter) zd1205_open,<br>/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4353 <br>zd1205: (exit) zd1205_open,<br>/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4436
<br>zd1205: (enter) zd1205_close,<br>/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4896<br>zd1211: failed rf reg_urb<br>zd1211:USB ST Code = -1 <br>zd1205: (exit) zd1205_close,<br>/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4962
<br><br>I should point out again, then when make $ ifconfig wlan0 up the<br>computer goes almost unresponsive due to high cpu usage or something.. <br>i have to wait like half a minute only to see the characters i typed<br>
into the console.<br><br>Good day to all,<br>Janes<br><br> </div>